Nexus Prosystems - ProJoint V75-WT (Epoxy Resin) - Buff
Product Code: SKU_08D9696D
A specialist solution to filling joints between paving slabs and setts, suitable for natural stone and concrete paving on pedestrian and vehicular areas with medium to heavy vehicle loads up to 7.5 tonnes.Read More...
- Home Delivery 5 Days Delivery (Monday to Friday)
- Click & Collect Available for Click & Collect
- In Store Our stores stock this product
- Two part resin based mortar system, cement free
- Medium to heavy traffic loads up to 7.5 tonnes, ideal for driveways and high traffic areas
- Fast application
- Easy: No more bending or kneeling and much less effort
- Applied to wet surfaces + increased water tolerance for use in light rain
- Professional results: No mess, and no returning for cleaning
- Self compacting and suitable for joint widths from 5mm upwards
- Weed, pressure washer and frost resistant
- Colours available: Neutral (buff), Mid-Grey and Black
Ensure the joints are cleaned out to a minimum depth of 25mm for 7.5t traffic loading, and a minimum joint width of 5mm. Paving must be firmly bedded and stable prior to filling joints and laid on bedding material suitable for the intended traffic loading. Liberally wet the paving prior to mixing allowing the water to soak into the surface.
V75-WT™ can be mixed in either a rotary concrete mixer or by using a drill and paddle. Add the sand to the mixer and when wearing appropriate PPE, pour the resin and hardener together and begin mixing. Mix for around two minutes until thoroughly mixed and then add 3 litres of water to the mix (equivalent to 2 of the resin containers). Mix for a further three minutes until the mix becomes a free flowing slurry.
Ensure that the paving is still wet and surface temperature is between 0°C and 25°C. Do not allow the paving to dry out during application and care should be taken when using the product on dark paving due to high surface temperatures. Empty the mix directly onto the paving and move the mix using a squeegee over the total area allowing the empty joints to fill completely.
After 10 to 15 minutes use a medium soft brush at 45° to joints and sweep off the excess sand leaving the paving clean. It is particularly important to sweep the paving clean before the product cures to ensure any remaining residue does not set on the paving surface. The fluid nature of the mortar means that no further compaction of the joint is required. A trowel or iron can be used if necessary once the mortar has begun to cure to achieve a traditional finish.
Increased water tolerance means that the product can be used in light rain but does need protecting from prolonged and heavy rain as this will delay the cure and could cause fluid damage. Make sure that any protective cover does not come into contact with the fresh joints; air circulation over joints is required during curing time. Cure times are dependant on temperature and humidity but as a guide can accept foot traffic after 12 hours and vehicle traffic after 24 hours.
V75-WT™ may highlight and enhance the natural surface colours and textures of the paving. This is only a temporary effect and weathering and foot traffic accelerate its disappearance.
|Joint Size||100 x 100mm Setts||450 x 450mm Slabs||600 x 600mm Slabs|
|5mm x 25mm Deep||8m2||34m2||45m2|
|10mm x 25mm Deep||4m2||17m2||22.5m2|
|15mm x 25mm Deep||2.67m2||11.3m2||15m2
Questions about any of our paving range? Call our paving experts on 0800 999 3055. Lines open Monday - Saturday 09:00 - 17:30. Calls charged at standard national rate
Need a sample? Why not order one of our sample kits
Our sample packs are completely free! We only ask you to pay for delivery due to freight weight costings.
Reviews For Nexus Prosystems - ProJoint V75-WT (Epoxy Resin) - Buff
Be the fist to review the Nexus Prosystems ProJoint V75-WT (Epoxy Resin) - Buff.